How To Use Acetylene Cutting Torch

How To Use Acetylene Cutting Torch. Depress cutting lever and adjust pressure if necessary This video will demonstrate the safe use of an oxygen acetylene torch to cut metal.

Construction Worker Using Oxyacetylene Torch HighRes from www.gettyimages.com

I prefer acetylene as i need portability. Whichever torch you are using, the lighting procedure is the same, as are the. Video goes over setting up an oxy axetylene torch.

Then, light the torch using the striker. Stand away from front of regulator;

Adjust the acetylene valve to where the flame is touching the tip. Also, basic procedures on how to shut it down, purge.

Video goes over setting up an oxy axetylene torch. Using your striker light the torch facing away from you and the bottles.

Adjust regulator p/a screws to tip pressure settings; Turn off torches after use:

The acetylene/oxygen mixture burns at a temperature of over 6,300 degrees fahrenheit. Jet of pure oxygen is blown through the llame onto the hot spot to melt or burn away the metal, the operation being carried on progressively along the line of the desired cut.

The acetylene/oxygen mixture burns at a temperature of over 6,300 degrees fahrenheit. Take the torch and connect the handle with hoses.

Remember, all the components make this torch more effective to heat, weld, braze, and cut like butter without making any problem. Now install the cutting torch.

Open acetylene valve on torch. Using your striker light the torch facing away from you and the bottles.

It doesn't matter how much. Safety check, turning on and actual use, and turning the equipment off.

The weight and bulk is less. Select the tip style for the fuel gas you are using and metal type/condition.

Take the torch and connect the handle with hoses. All the cutting torch equipment we've looked at so far can either be used with acetylene or propane.

Here are five easy steps. Less heat per volume of gas with propane.

Jet of pure oxygen is blown through the llame onto the hot spot to melt or burn away the metal, the operation being carried on progressively along the line of the desired cut. As is well known, metal cutting torches l utilize a mixture of fuel gas and pure oxygen discharged in a composite jet llame adapted to locally heat the metal to a high temperature, whereupon a.

Using your striker light the torch facing away from you and the bottles. Propane is not applicable for welding.

Light flame (striker should be about ¼ to ½ inch from tip). Ensure only to fasten the coupling nut with your hands to prevent any damage to the o rings.

Depress cutting lever and adjust pressure if necessary Having said that, it cuts just as well as acetylene and the cost is a bit less.

Close oxygen valve on torch. Adjust the acetylene valve to where the flame is touching the tip of the torch, but is not giving off black smoke.

Adjust the acetylene valve to where the flame is touching the tip of the torch, but is not giving off black smoke. Light torch with flint striker:

For better practice, we suggest you use hoses of different colors like green for oxygen and red for acetylene. As is well known, metal cutting torches l utilize a mixture of fuel gas and pure oxygen discharged in a composite jet llame adapted to locally heat the metal to a high temperature, whereupon a.

Adjust regulator p/a screws to tip pressure settings; Close oxygen valve on torch.

Since The Advent Of Arc Welding, Very Little Industrial Work Is Still Performed With The Oxy/Fuel Process.

Now install the cutting torch. Open acetylene valve on torch. This can be found at the bottom of the handle.

A Yellow Flame Should Appear When You Do This.

Light flame (striker should be about ¼ to ½ inch from tip). This video will demonstrate the safe use of an oxygen acetylene torch to cut metal. You can;t heat as big a block of metal nor cut as thick with the same torch.

Select The Tip Style For The Fuel Gas You Are Using And Metal Type/Condition.

As the terms suggest, one torch is used to cut metals, the other is used to join (weld) metals. Also, basic procedures on how to shut it down, purge. Propane is not applicable for welding.

Remember, All The Components Make This Torch More Effective To Heat, Weld, Braze, And Cut Like Butter Without Making Any Problem.

The only advantage of acetylene is you can use it in all tasks in your workshop. Close oxygen valve on torch. The weight and bulk is less.

Open The Valves Of Both Tanks, But Do It Slowly And Only One At A Time.

Safety check, turning on and actual use, and turning the equipment off. Using your striker light the torch facing away from you and the bottles. Adjust the acetylene to get rid of the black smoke.

Bagikan Artikel ini